Please call 1-877-GO ALTEC, Option 1, to check availability.
This item cannot be ordered online but please call us at 1-877-GO ALTEC, Option 1 to place an order.
This item cannot be ordered online but please call us at 1-877-GO ALTEC, Option 1 to place an order.
Add to List
Create New Shopping List
Would you like to add {{productName}} to an existing shopping list or add to a new list?
Would you like to add {{productName}} to an existing shopping list or add to a new list?
Ambiguous Address
The Address validation service does not recognize this address. Using this address could cause a delay in your shipment or your shipment being returned to the shipper. Would you like proceed with this address?
Leaving Altec Store.
You are about to leave the Altec Store. Do you wish to continue?
We Are Unable To Process Your Request At This Time.
We are currently experiencing technical difficulties and are unable to process your request.
The Wright Drive was created and patented by the Wright Tool Company, taking full advantage of advanced CAD/CAM technologies. It actually improves the torque load capabilities of every fastener, whether it’s a soft stove bolt or a hardened aerospace fastener
Torque loads are moved away from fastener corners to prevent rounding
Stress is distributed over a much larger area of the fastener
Leverage is improved, eliminating fastener rounding and increasing tool strength
Tool-to-fastener contact area is ten times greater than with a conventional design, and almost twice that of a First Generation AS954 tool
Includes:
4314 - 7/16" 8 Pt. Standard Socket
4316 - 1/2" 8 Pt. Standard Socket
4318 - 9/16" 8 Pt. Standard Socket
4320 - 5/8" 8 Pt. Standard Socket
4322 - 11/16" 8 Pt. Standard Socket
4324 - 3/4" 8 Pt. Standard Socket
4326 - 13/16" 8 Pt. Standard Socket
4328 - 7/8" 8 Pt. Standard Socket
4330 - 15/16" 8 Pt. Standard Socket
4332 - 1" 8 Pt. Standard Socket
4334 - 1-1/16" 8 Pt. Standard Socket
4336 - 1-1/8" 8 Pt. Standard Socket
4340 - 1-1/4" 8 Pt. Standard Socket
2-W010 - Rails
W4 - 13 Clips
Safety:
Users and bystanders must wear safety goggles
To avoid possible eye injury from flying objects, safety goggles or equivalent protection conforming to ANSI Z87.1 shall be worn and kept clean by the user and all persons in the immediate area where any tool is being used
Do not hold impact sockets, universal joints or extensions while an impact tool is running. Serious hand injury can occur
3/4” drive and larger drive size impact sockets require the use of a ret ring or a Pin & O-ring to secure the socket to the driving square
Never use a nail or homemade pin for holding a socket in place
Never exceed the manufacturer’s gun pressure rating
Impact sockets are to be used to turn (tighten or loosen) fasteners while being driven by a power, impact or hydraulic driver
Never dwell on a socket after it has stopped running. This can damage both the socket and the fastener
Place the socket all the way on the fastener before starting the gun
Adaptor strength is limited to the smallest drive square member
Mind the joints between the gun and fasteners for less loss of torque and less wear
Use the correct size socket, do not use metric sockets on inch fasteners or inch sockets on metric fasteners, because the fit is not good enough. Do not use hex sockets on square fasteners or square sockets on hex fasteners
Never use sockets as a driver for hex or square bits or shafts
Large drive impact sockets are inherently heavy and care needs to be taken during handling
Socket opening configurations shall be inspected before each use and their use discontinued at the first sign of significant wrenching surface deterioration
Inspect and discard worn or cracked sockets
Number of Pieces - 13
Drive Size - 1/2"
We use cookies on our site to provide you with the best user experience. This data may be used for personalization, analytics, and ads. Disabling cookies may also prevent parts of website from working properly.